Standard: Meets EN361,EN358 Material: 100% polyester, the strech is 45mm, breaking load is no less than 23kN for all types. Buckle: Sheet steel, heat treated, Min. breaking load:18 kN, Zinc plated Rings: Forged steel, heat treated, 100% proof loaded to 16kN, Min. breaking load is 23kN, Zinc plated.
GH3002 Multiple adjustable for safety harness
Standard: Meets EN361,EN358
Material: 100% polyester, the strech is 45mm, breaking load is no less than 23kN for all types.
Buckle: Sheet steel, heat treated, Min. breaking load:18 kN, Zinc plated
Rings: Forged steel, heat treated, 100% proof loaded to 16kN, Min. breaking load is 23kN, Zinc plated.
Attachments:Dorsal Sternal Lateral
Adjustable: Chest, Shoulder, Waist, Legs
Tested by 140kgs
In this case, a suitable energy absorbing lanyard has to be used, so that the maximum force of the shock after an eventual fall, is reduce to less than 6 kN.(Max.140kg; user + equipment) Please follow using instruction manual!
How to wear full body safety harness
1.Take the harness out from the package, holdding it by the dorsal tightening ring.
2.Wear the harness by shipping on the shoulder straps one after one, taking care not twist them. Adjust them by pulling or releasing the slack end, so that the buttock strap is firmly in place under the buttocks. Pull one and the other thigh strap through the crotch and latch each strap. Make sure not to cross the straps.
3.Harness closures and keepers ensure proper harness fit, which is of fundamental importance for safe use. Chest straps should fit across the middle of the sternum, not higher or lower. Leg straps should be snug. Adjusting the leg straps too loosely will cause injuries in the case of a fall. Correct harness adjustments will place the sub-pelvic strap snugly below the buttocks, the position necessary both to absorb energy in the case of a fall, but also to provide some relief from suspension trauma after a fall has occurred. Correct sub-pelvic position is the result of correct combination of all the harness adjustments.
1)Ensure straps are not twisted and the loose end is on the outside.
2)Pass the buckle with the center bar through the open buckle. The slot will asssist. Tug to ensure buckle is in place.
3)Pull the webbing to tighten the strap so there is a snug fit.
4)User MUST slide plastic keepers to strap end or find other location to truck end to ensure there are no loose and dangling ends.
5.Torso Length Adjuster
1)The torso adjuster ensures the overall fit of the harness. Check to see the sub pelvic strap is situated below the buttocks. If it is too high the torso adjuster should be loosened to lower the sub-pelvic strap. If it is too low the torso adjuster can be tightened to raise the sub-pelvic strap.
2)To shorten or lengthen the torso webbing push the top of the torso adjuster down so it is horizontal.
3)Separate the small mating buckle from the larger pass-through to allow web to flow through the torso adjustment.
4)When at the right length, slide the lower plastic keeper down near the torso adjuster and the upper plastic keeper up so the webbing end is not dangling.
All webbing ends are equipped with plastic webbing keepers, which are important to the safe use of the harness.Sliding one keeper close to the buckles ensures the buckle can't be accidently opened or moved while in use. Sliding the other close to the end of the strap keeps if from being loose and dangling and a possible snag hazard.
If you are interested in our products of GH3002 safety harness, please feel free to contact with us.
Contact way as below:
Fax: 0086-23-86076692, 86076693
Cell phone/Whatsapp/Wechat: 0086 1782381834